Launch League

Construction trade · Ontario · Trade code 308R

Residential (Low Rise) Sheet Metal Installer

Residential Sheet Metal Installers put in the ducts that carry heated and cooled air through new houses. You measure, cut and fit metal and connect it to furnaces and vents.

What you'd do

  • Read house plans to lay out duct runs
  • Cut and shape metal duct and fittings
  • Hang and connect ducts in walls and ceilings
  • Install vents and ventilation fans
  • Seal joints and check airflow

Who hires

Residential HVAC contractorsHome builders

Who it suits

Suits someone who likes hands-on construction work, measuring, and moving through a house build as it takes shape.

The setting: Mostly indoor work in new low-rise homes, fitting metal ducts in attics, basements and crawl spaces, with repetitive tasks, lifting and tight spaces.

Try it first, this month

Take a construction tech class and ask a local heating and cooling or sheet metal company about a job shadow day. Building a small project from a drawing is good practice.

Or watch it done: Visit a trade school open house to see duct layout and fitting demonstrated on a mock home frame. Watch only: never do regulated or risky work to try a trade.

The official route

The Residential (Low Rise) Sheet Metal Installer apprenticeship

These facts are copied from Skilled Trades Ontario's Apprenticeship Programs Quick Facts Chart.

Trade code
308R
Classification
Compulsory. You must be a registered apprentice or hold a certificate to work in this trade.
Certifying exam
Yes. Passing it earns a Certificate of Qualification.
Red Seal in Ontario
No
Minimum education
Grade 10
In-school training
360 hours, 2 levels
On-the-job training
4,140 hours
Total
4,500 hours (approximately two and a half years, by Skilled Trades Ontario's estimate)
Hours or competency
Hours-based: you must complete the full prescribed hours on the job, and a ratio of 1 journeyperson to 1 apprentice applies.
Status
Active. Taking new registrations.

What school covers

Trade skills and practicesTools, ladders and scaffoldingCodes and manualsSketches and drawingsDuct installationHome construction and airflow

Where the in-school training happens

In-school levels are taught by training delivery agents the province approves, mostly colleges and some union training centres. Your sponsor and Skilled Trades Ontario will tell you where your level runs. Ontario does not publish one list by trade.

How to start

  1. In high school, get close to the work

    Take the matching tech class, ask about co-op, and look at OYAP and the SHSM.
  2. Meet the entry standard (Grade 10)

    You must also be at least 16 and allowed to work in Canada.
  3. Find a sponsor

    Usually an employer or a union who agrees to train you through the whole program. For this trade, Support Ontario Youth's group sponsorship can register and sponsor you on an employer's behalf, if you are hired by an employer that works with them.
  4. Register with Skilled Trades Ontario

    You and your sponsor sign a training agreement. At 16 or 17 you apply with a parent or guardian's consent.
  5. Train, log your skills, and certify

    Finish your hours and in-school levels, then write the certifying exam for your Certificate of Qualification.

Safety training: on construction projects, Ontario requires anyone who uses fall protection to complete an approved working at heights program. Ask your employer which safety courses you need before your first day.

Sources: Skilled Trades Ontario: Residential (Low Rise) Sheet Metal Installer and Skilled Trades Ontario, Apprenticeship Programs Quick Facts Chart (updated June 2026). Check both before you register: programs and training availability change.

Grants, loans and bonuses

Money you may be able to get

What applies to a Residential (Low Rise) Sheet Metal Installer apprentice in Ontario, based on this trade's sector and Red Seal status. Each program has its own conditions, so check the official page before you count on it.

Ontario Tools Grant

$600

After you finish (or are exempted from) level one in-class training and have been registered at least 12 months. Taxable, not repaid.

Official page

Apprentice Development Benefit

Living, travel and child care costs

While you attend full-time in-class training at a ministry-approved training delivery agent.

Official page

Ontario Apprenticeship Completion Bonus

$2,000

When you finish a non-Red Seal trade and are out of high school. Apply within 180 days of your certificate. Taxable.

Official page

Employment Insurance

EI benefits

Eligible apprentices can get EI while attending technical training.

Official page

SOY Education Scholarship

One of 10 awards of $500

For registered Ontario apprentices at Level 2 or higher, any trade. Paid to your school toward fees. Check whether the current round is open.

Official page

Read on ontario.ca, canada.ca and supportontarioyouth.ca on 8 November 2026. Not in school yet? Ontario's pre-apprenticeship training is free, including books, safety gear and tools. See every program in our apprenticeship grants guide.

Get ready now

Start before you apply

What to learn and make while you are still in school, so you walk into an employer's shop with something to show.

Skills to start building

Duct layoutAirflow basicsReading house plansMeasuring and geometry

Make something to show

Draw a simple duct layout for a fictional small house, with a materials list.

Paper and screen only. Bring it to a job shadow or interview.

Who to talk to first

A residential heating and ventilation contractor, a union local for the trade, or the school OYAP recruiter.

In high school? Your OYAP recruiter can arrange placements once you are 15, in Grade 11 or 12, with at least 14 credits.

Where it can lead

Paths people take after they certify, with more experience or more training.

Installer leadSheet metal journeypersonVentilation contractorSite supervisor

Ask an employer

Before you sign on, or on a job shadow day.

  • How does this trade differ from the broader sheet metal trade, and which should I register in?
  • How steady is new home work through the winter months?

What it pays in Ontario

Job Bank's Ontario figures for NOC 72102, Sheet metal workers, the occupation group this trade falls in. They cover everyone in that group, not only certified tradespeople. Apprentices are usually paid less while they train.

Low
$22.94
Median
$35.00
High
$48.17

Per hour, reference period 2023-2024, updated by Job Bank November 19, 2025. Job Bank rates the 3-year outlook in Ontario as "Limited" (2025-2027). See the Job Bank report.

Want the longer version, with a day in the job and who hates it? Read our full career guide.

Questions people ask

Do you need a licence to work as a Residential (Low Rise) Sheet Metal Installer in Ontario?
Yes. Residential (Low Rise) Sheet Metal Installer is a compulsory trade, so to work in it legally you must be a registered apprentice, or hold a Provisional Certificate of Qualification or a Certificate of Qualification, and appear on the Skilled Trades Ontario Public Register.
How long is the Residential (Low Rise) Sheet Metal Installer apprenticeship?
4,500 hours in total: 4,140 on the job and 360 in school, over 2 levels of in-school training. Skilled Trades Ontario puts that at approximately two and a half years.
Is Residential (Low Rise) Sheet Metal Installer a Red Seal trade?
Not in Ontario. Certification is provincial.
What grants can a Residential (Low Rise) Sheet Metal Installer apprentice get in Ontario?
Ontario's Tools Grant is 600 for construction trades, paid after level one and 12 months of registration. As a non-Red Seal trade, you may get Ontario's $2,000 Apprenticeship Completion Bonus when you finish. The Apprentice Development Benefit and Employment Insurance can help while you are in class.
What do you need to start?
The minimum education to register is Grade 10. You must be at least 16, be allowed to work in Canada, and have a sponsor, usually an employer, who agrees to train you.